Using BitLocker Drive Preparation Tool with Command Prompt
We accept previously read most the BitLocker characteristic, where nosotros've mentioned the BitLocker Bulldoze Training Tool. This tool is currently not available as a download for Windows 111/0/8/7/Server. Just if yous nevertheless desire to use the abilities of this tool, and so you can utilize the command-line tool. In this commodity, nosotros will talk about using the BitLocker Drive Training Tool using Control Prompt in Windows 10.
Basically, BitLocker Bulldoze Preparation tool prepares a difficult drive with the partitions necessary for BitLocker Drive Encryption. Near installations of Windows 7 or later recognize the command-line tool. Here is how yous can use it.
Using BitLocker Drive Preparation Tool via Control Prompt in Windows
1. In club to employ BitLocker Drive Preparation command-line tool, open the administrative Command Prompt.
2. Next, y'all tin can apply the following control with suitable descriptors mentioned below and printing Enter:
bdehdcfg [–driveinfo <DriveLetter>] [-target {default|unallocated|<DriveLetter> shrink|<DriveLetter> merge}] [–newdriveletter] [–size <SizeinMB>] [-quiet] The in a higher place-mentioned command is in general form and its variable parameters can be altered using the following descriptors:
This displays the drive letter, the total size, the maximum costless space, and the partition characteristics. Only valid partitions are listed. Unallocated space is not listed if four primary or extended partitions already exist-
-driveinfo <DriveLetter>:
Example: To display data for C: drive, use bdehdcfg –driveinfo C: control.
Prepares a partition for use as a system drive by BitLocker and Windows Recovery. By default, this partition is created without a drive letter-
-target {default|unallocated|<DriveLetter> shrink|<DriveLetter> merge} Instance: In order to utilize this control to designate an existing drive (Thou) as the organisation drive, apply bdehdcfg -target Chiliad: merge at Control Prompt.
Assigns a new bulldoze letter to the portion of a bulldoze used as the system drive. Equally a best exercise, it is recommended that you do non assign a drive letter to your system drive-
-newdriveletter
Instance: Using control bdehdcfg -target default -newdriveletter Grand: illustrates that default drive is being assigned the drive letter of the alphabet K.
Specifies the size of the organization segmentation when a new system drive is being created. The default is 300 MB in minimum size is 100 MB-
-size <SizeinMB>
Example: Apply command bdehdcfg -target default -size 500 to classify 500 MB to the default system drive.
Informs the BitLocker Drive Preparation Tool that all actions and errors are not to be displayed in the control-line interface-
-quite
Example : bdehdcfg -target default -quiet
Use this to restart BitLocker Drive Preparation Tool after an operation is completed-
-restart
Case: BdeHdCfg.exe -target d: merge -quiet -restart
In this way, yous can use the BitLocker Drive Preparation control-line tool.
Interested readers may visit TechNet and KB933246 to find out further possibilities.
Run into this mail service if y'all receive BitLocker Bulldoze Encryption cannot be used because critical BitLocker system files are missing or corrupted (0x8031004A) error.
Related reads:
- BitLocker To Become in Windows
- Recover files & data from inaccessible BitLocker encrypted drive
- Encrypt USB Flash Drives with BitLocker To Go
- BitLocker Setup could not find a target arrangement drive to ready
- BitLocker Setup failed to consign the BCD (Kick Configuration Information) store
- Your Recovery Key Couldn't Be Saved To This Location error for BitLocker.
Source: https://www.thewindowsclub.com/bitlocker-drive-preparation-tool-windows
Posted by: bachmannpeng1938.blogspot.com
0 Response to "Using BitLocker Drive Preparation Tool with Command Prompt"
Post a Comment